OPGW/ADSS Hardware - Page 1 Total 11

Hardware For ADSS & OPGW Cable

Tension Clamp are designed to connect OPGW cables and tensile poles (or towers). Armor rods can protect and provide cushioning to the OPGW cables. The special design of Armor rods makes ensure that opgw tension clamps can not cause undue stress to the OPGW cables, so that the normal lifetime of cable system is ensured. Helical Tension Set OPGW is mainly used for installation of cable with less tha

Preformed Tension Clamp for OPGW Cable
The guide clamp is used to guide OPGW cable down steel towers, steel poles, concrete poles and wood poles to splice locations. The Guide Clamps may be bolted to the tower or poles. Additionally, adapters are available for the steel towers and steel and concrete poles. Guide Clamps are typically two groove clamps spaced five to eight feet apart to help maintain alignment of and support the OPGW

Guide Clamps For OPGW
Single suspension cla

Preformed Helical Tension Set For OPGW/ADSS Cable
The double layer formed wire suspension is for use on optical ground wire (OPGW) cables. Available with single or double suspensions.

Double Layer Formed Wire Suspension for OPGW
Downlead clamps are used to secure the OPGW fiber optic cable as it is trained down the pole or tower.

Downlead Clamp For OPGW
Vibration dampers work to cancel damaging fatigue caused by wind-induced vibration. Most tuned damping devices operate best near their natural frequencies.

OPGW Vibration Damper
FIBERFUTURE® offers wedge dead ends that ease and speed ADSS cable installation. The ADSS wedge dead end is ideal in crowded distribution environments because its shorter length allows for safer and efficient installation. The wedge dead end comes with all parts assembled. The side plates are properly aligned with spacers and self-locking hex bolts, as well as retainers.

ADSS Wedge Dead End
FIBERFUTURE® is 19 Years Experienced Professional Manufacturer of Fiber Optical Cable & Accessories, we can supply all types of ADSS Cable Fittings, and OEM/ODM Service Available.

ADSS Hardware Products
ADSS J hook suspension clamps are designed to provide a suspension for aerial ADSS cable at intermediate poles on cable routes on access network. Span up to 100 meters.

ADSS J Hook Suspension Clamp
ADSS double suspension clamp with preformed armor rods is used to suspend ADSS cable.

ADSS Double Suspension Clamp
Anchoring clamp is self-adjusting, designed to anchor ADSS optical fiber cable transmission lines. The clamp consists of self-adjusting plastic wedges, which clamp the optical cable without damaging. Wide range of gripping capacities and mechanical resistance archived by wide product range and different models of ADSS anchor clamps.

ADSS Anchoring Clamp Dead End Clamp

FIBERFUTURE product line consists of fiber optic cable, optical connectivity, fusion splicers, and test equipment, as well as fiber management systems, closures, and accessories. Included in accessories are different types of hardware for the installation and efficiency of your cable system. We provide years of experience and excellent solutions for your hardware needs in both ADSS (All-Dielectric Self Supporting), OPGW (Optical Ground Wire), and other cable calmps. Please follow the links below for assistance in choosing your hardware.

OPGW cable Hardware

Image	Product Name	Inquire
	FDH(Fiber Distribution Hub) The FDH is designed and constructed to be suitable for outdoor installation. The housing is sufficiently sturdy to withstand typical handling and installation procedures. The design and layout of the cable guides promote an efficient and ordered positioning of the cable within the hub.	Inquire
	Joint Box Suitable for OPGW cable connection protection, has the function for direct connections and divergence connection, which can out of 4 cable, installed in the overhead pole, tower.	Inquire
	Clamp Clamps are used to guide OPGW cables from the top of the structure to the joint box or for grounding the cable. TFO provide proper spacing and holding strength without damaging the cable.	Inquire
	Tension Assembly Tension Assembly is used for OPGW cable route’s fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower etc.	Inquire
	Vibration Damper Vibration Dampers effectively reduce the level of Aeolian vibrations on OPGW cables. It respond to wind induced line vibrations that is characterized by high frequency, low amplitude motion.	Inquire
	Suspension Assembly Suspension Assembles are designed for use with OPGW cable at suspension tower positions. Suspension Assemblies reduce static compressive stresses at the support point and cushion the OPGW cable against the dynamic stress of Aeolian vibration.	Inquire
	Downlead Clamps for OPGW	Inquire
	Downlead Clamps for OPGW and ADSS	Inquire

OPGW cable Hardware

Image	Product Name	Inquire
	Formed Wire Dead End for ADSS Cable	Inquire
	Formed Wire Suspension for ADSS Cable	Inquire
	ADSS Suspension Unit	Inquire
	Downlead Clamp for ADSS	Inquire
	ADSS Temporary Grip	Inquire
	Fiber Storage Units for ADSS Fiber Optic Cable	Inquire
	ADSS J Hook Suspension Clamp	Inquire
	ADSS Anchoring Clamp Dead End Clamp	Inquire

FAQS of OPGW Hardware

Q

Sample free or needed to pay first?

A

If you don’t need to print a custom mark or other special material or structure on the products, it will not charge any cost. Just tell us your freight collect account like FedEx DHL TNT. If you don’t have an account, it needs to charge Express fee properly.
Q

What is your MOQ?

A

Stocked model 1km above Custom length/structure/materials, MOQ 2km-10km
Q

How can I get a quick quote?

A

Getting a quote from Hunan GL is easy and reliable. You can get in touch with our online service with inquiry details. Or email us inquiry at sales@hunangl.com. Our experts will get back to you in 1-12 hours.
Q

How long is your delivery time

A

5-10 days if the goods are in stock. 2-3 weeks if the goods are not in stock, mostly depends on quantity and production plan.